-
product
Manual Test Adapters
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
product
Solar Radiation (Sunshine) Test
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe st...show more -
product
Test Services for EMC Compliance and Safety
Parker Chomerics offers a wide variety of EMI/EMC and safety testing for regulatory compliance. Tests include FCC, EC, VCCI, IEC 1000 (formally 801) EN 61000 Series, CISPR, Austel, MIL-STD-461 and EU regulations
-
product
Test Probes
Petracarbon is a leading supplier and provider of spring contact probes and semiconductor test sockets.
-
product
2-way Radio Signaling Test Software
Tone Generator
The new PC-based test software for RF communications engineers and technicians. Flexible, accurate code synthesizer for simulation and testing of 2-way radio systems, repeaters, remote control, ANI, Paging and more.No external hardware required.
-
product
Custom, 18-Slot, Front to Rear Cooling, AC Supercomputer Application
Barracuda 648 CS7500
Supercomputer application.
-
product
Test System
LB301
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
product
ADAS Related Test Solutions
Getting sensor fusion testing off the road! Active safety systems for autonomous vehicles require millions of miles of test-drives to meet all safety requirements.
-
product
Test & Calibration
Gamma Scientific is ISO/IEC 17025 accredited by NVLAP (NVLAP lab code 200823-0). In addition to assurance of measurement accuracy, accreditation ensures traceability to known standards, provides international acceptance of measured values, and is important for compliance purposes for your own ISO/IEC certifications. Our state-of-the-art, ISO 17025 accredited calibration laboratories in San Diego, California offer a range of test and calibration services including:
-
product
Flying Prober Test System
QTOUCH1404C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
product
TEST SOCKET
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
product
Single Mode Multimode Test Inspect Kit
KI-TK072A
1310/1550/1625 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable SC/APC & LC/APC connectors
-
product
Web Application / Services Testing Tool
JMeter™
The Apache Software Foundation
Apache JMeter may be used to test performance both on static and dynamic resources (Webservices (SOAP/REST), Web dynamic languages - PHP, Java, ASP.NET, Files, etc. -, Java Objects, Data Bases and Queries, FTP Servers and more). It can be used to simulate a heavy load on a server, group of servers, network or object to test its strength or to analyze overall performance under different load types. You can use it to make a graphical analysis of performance or to test your server/script/object behavior under heavy concurrent load.
-
product
Abnormal Sound Test Software
Signal extraction, real-time curvesProfessional database of each productQuantitative values of abnormal soundSophisticated signal processing techniquesAbnormal sound -- not noise but special sound downed in signals
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal ...show more -
product
Diagnostic Test System™
The original Teseda system for bench-top stimulus, test pattern debug, validation, device failure mode stimulation in-situ with other Failure Analysis lab equipment such as an EMMI, etc.
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
Relay Test Set
Relay testing equipment is a portable apparatus designed for checking the operating characteristics of protective relays on site. Rr Relay Testing Equipments are designed to facilitate routine test or periodic maintenance test of relays by simulating (as early as possible) fault conditions under which the protective relays are required to function. There are several approaches to the method of testing relays on site. The Relay Testing Equipments are secondary injection type and are intended to be used to test the relays after isolating them from live systems, either physically or electrically.
-
product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
product
Custom Test Targets & Charts
Our customers in industries that require camera or scanner image evaluation certainly know the challenges that come from finding the perfect target for a specific system and measurement. Thankfully, we at APPLIED IMAGE know these challenges just as well. The ability to freely customize a target has proved important for our customers to get the image evaluation tools they need. Our sales engineers are experts in different types of targets and specifications that will give you the best results for your project, and will guide you through the process from start to finish.
-
product
Thermal Cycling and Humidity-Freeze Test
King Design Industrial Co., Ltd.
*10.4" TFT LCD, touch-type Chinese/English display controller.*Temperature/humidity setting procedure, LCD curve display device (set to “curve display”).*Chinese/English/LCD operation/troubleshoot/guiding window.*State-of-the-art intelligent auto-dispatch “heat load value” coolant servo valve flowrate algorithm control.
-
product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Galaxy Craft Test Set
A low cost, high quality test set. Galaxy is made of industrial grade plastic. It is designed for rugged use and can withstand rough handling and shocks in field use. The dumbbell shape is slung on the shoulder to keep the hands free, It has an extra large belt hook equipped with a spring-loaded clip for secure holding to belt loops. The line cord is braided in superior yarn with angled bed of nails and piercing pin.
-
product
Dielectric Strength Test Apparatus
CX-KD12
Shenzhen Chuangxin Instruments Co., Ltd.
To improve the insulation board and creepage dielectric properties, surface brushed polished, bottom bracket the minimum distance from the edge of >35mm, the altitude of 2000 meters designed to meet the strength test requirements of 12KV
-
product
Camera Barrel Test System
BK8612
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
-
product
Power Functional Test with Energy Saving Solutions
Power System
The Power System is a test platform conceived to verify and certify the operation of power modules.The complete structure, combining two Multi standard cabinets, is sized to contain all of the resources required for testing: drive/sense modules, power modules and load simulators.In this tester, in addition to strictly perform the requested measurement as per technical specifications, the issues of consumptions and dissipations were taken into account, integrating an Energy Recovery circuit which enables reuse of output energy to supply the system.